A big thank you Daniel.
I was a bit lost at first sight with the Analog Way protocols but finally it is not so complicated.
Here are the different commands I've found (tested and approved), if it might help others :
- For a
Single MEMORY (PRESET) -
. 1) Select a SCREEN (where to load the Memory) :
TCPSend,DeviceID,
0PMscf[LF] (Screen 1 = 0 ; Screen 2 = 1 ...)
. 2) Load a Memory at Preview (in the Screen selected) :
TCPSend,DeviceID,2047PMcat[LF]
TCPSend,DeviceID,1PMlse[LF]
TCPSend,DeviceID,
0PMmet[LF] (selection of the Memory to load / Memory 1 = 0 : Memory 2 = 1 ...)
TCPSend,DeviceID,
1PMprf[LF] (selection of Preview or Program to load the Memory / Program = 0 ; Preview = 1)
TCPSend,DeviceID,1PMloa[LF]
. 3) TAKE (in the Screen selected) :
TCPSend,DeviceID,1PMlot[LF]
. 4a) Load & Take a Memory (in the Screen selected) :
TCPSend,DeviceID,2047PMcat[LF]
TCPSend,DeviceID,1PMlse[LF]
TCPSend,DeviceID,
0PMmet[LF] (selection of the Memory to load / Memory 1 = 0 : Memory 2 = 1 ...)
TCPSend,DeviceID,
1PMprf[LF] (selection of Preview or Program to load the Memory / Program = 0 ; Preview = 1)
TCPSend,DeviceID,1PMloa[LF]
TCPSend,DeviceID,1PMlot[LF]
. 4b) Load & Take a Memory (in a specific Screen) :
TCPSend,DeviceID,2047PMcat[LF]
TCPSend,DeviceID,1PMlse[LF]
TCPSend,DeviceID,
0PMscf[LF] (selection of the Screen where to load the Memory / Screen 1 = 0 : Screen 2 = 1 ...)
TCPSend,DeviceID,
0PMmet[LF] (selection of the Memory to load / Memory 1 = 0 : Memory 2 = 1 ...)
TCPSend,DeviceID,
1PMprf[LF] (selection of Preview or Program to load the Memory / Program = 0 ; Preview = 1)
TCPSend,DeviceID,1PMloa[LF]
TCPSend,DeviceID,1PMlot[LF]
- For a
MASTER MEMORY (One PRESET with specific MEMORIES for different Screens at the same time) -
. 1) Load a Master Memory at Preview :
TCPSend,DeviceID,2047PMcat[LF]
TCPSend,DeviceID,1PMlse[LF]
TCPSend,DeviceID,
0PSmet[LF] (selection of the Master Memory to load / Master Memory 1 = 0 ; Master Memory 2 = 1 ...)
TCPSend,DeviceID,
1PSprf[LF] (selection of Preview or Program to load the Master Memory / Program = 0 ; Preview = 1)
TCPSend,DeviceID,1PSloa[LF]
. 2) TAKE :
TCPSend,DeviceID,1PSlot[LF]
. 3) Load & Take a Master Memory :
TCPSend,DeviceID,2047PMcat[LF]
TCPSend,DeviceID,1PMlse[LF]
TCPSend,DeviceID,
0PSmet[LF] (selection of the Master Memory to load / Master Memory 1 = 0 ; Master Memory 2 = 1 ...)
TCPSend,DeviceID,
1PSprf[LF] (selection of Preview or Program to load the Master Memory / Program = 0 ; Preview = 1)
TCPSend,DeviceID,1PSloa[LF]
TCPSend,DeviceID,1PSlot[LF]
Have fun !