Client watchdog

Christie Pandoras Box Version 5

Moderator: Moderator Group

Client watchdog

Postby andreax » Sat Oct 14, 2017 3:32 pm

Hi all,
I have an installation where there are 12 projectors connected to 12 PC with Pandoras box client (latest 5 version) controlled by a Manager.
When the projectors are powered off, the PC doesn't "sense" the output anymore and goes into VGA setting causing Pandoras box client to hang.
Is there a way to monitor this hangs (the manager knows that a client is not operative anymore) within the Manager or (better) with an external watchdog so that I can kill it and restart it?
Thanks!
Andrea
andreax
 
Posts: 33
Joined: Thu Aug 02, 2012 6:02 pm

Re: Client watchdog

Postby malkuth23 » Sun Oct 15, 2017 2:39 am

You can see what the health node in WD (if you have WD Pro) reports back and probably use that to re-launch, but the best (or primary) solution should be to put an EDID manager on the outputs so this problem does not happen.
Matthew Newman-Saul
Theatrical Concepts
mattns@theatrical.com
User avatar
malkuth23
 
Posts: 354
Joined: Tue Apr 20, 2010 7:14 pm
Location: New Orleans, LA

Re: Client watchdog

Postby justyn roy » Sun Oct 15, 2017 3:23 am

Why not use the same command that turns off the projector to also exit the Client.
You could also use the same commands that turn the projectors back on to start the Client after a delay.
Justyn Roy

Online Manual
User avatar
justyn roy
 
Posts: 132
Joined: Tue Sep 27, 2016 1:26 am

Re: Client watchdog

Postby Benni_M » Sun Oct 15, 2017 4:21 pm

Do you have a Nvidia Quadro Card installed?
If yes you can set a EDID directly in the Nvidia Setup.

Best Regards,
Benni
Benni_M
 
Posts: 148
Joined: Thu Apr 12, 2012 3:45 pm

Re: Client watchdog

Postby andreax » Sun Oct 15, 2017 9:09 pm

malkuth23 wrote:You can see what the health node in WD (if you have WD Pro) reports back and probably use that to re-launch

I don't have WD Pro
But the best (or primary) solution should be to put an EDID manager on the outputs so this problem does not happen.

Too bad that this installation is 6 hours far from me :(
I'll keep in mind for the next installation, in the meanwhile...other ideas?

Justyn Roy wrote:Why not use the same command that turns off the projector to also exit the Client.
You could also use the same commands that turn the projectors back on to start the Client after a delay.

The projector are not software controlled, the customer turns them on and off with the remote

Benni_M wrote:Do you have a Nvidia Quadro Card installed?
If yes you can set a EDID directly in the Nvidia Setup.


Nice one! I'll check it!
Thanks!
andreax
 
Posts: 33
Joined: Thu Aug 02, 2012 6:02 pm

Re: Client watchdog

Postby justyn roy » Mon Oct 16, 2017 3:03 pm

Remote controlled...
So the client has a step to turn on the projectors anyways - perhaps add a step to push a button in WD to start the Clients?
Justyn Roy

Online Manual
User avatar
justyn roy
 
Posts: 132
Joined: Tue Sep 27, 2016 1:26 am

Re: Client watchdog

Postby andreax » Wed Oct 18, 2017 10:10 am

Justyn Roy wrote:Remote controlled...
So the client has a step to turn on the projectors anyways - perhaps add a step to push a button in WD to start the Clients?


I can't remote controll the projectors :(
andreax
 
Posts: 33
Joined: Thu Aug 02, 2012 6:02 pm


Return to Pandoras Box V5

Who is online

Users browsing this forum: No registered users and 1 guest

cron